Kitchen Sink Drain Leak: How to Fix It

A kitchen sink drain leak usually starts small: a damp spot under the sink, a musty smell in the cabinet, or a puddle that appears only when you run the dishwasher. Left alone, that slow drip soaks the cabinet floor, warps particleboard, feeds mold, and can damage the flooring underneath. The good news is that most kitchen sink drain leaks come from just three places, and two of them can be fixed in under an hour with basic hand tools. Here is how to find it and fix it.

Key takeaway: Most kitchen sink drain leaks come from a loose slip-joint nut, a worn P-trap washer, or a failed basket strainer seal. Dry everything, run the water, and watch where the first drip appears. Slip joints and P-traps are usually a 30 to 60 minute DIY fix; a leaking strainer takes a bit longer but needs no special tools.

Where Kitchen Sink Drain Leaks Start

Under a kitchen sink, the drain assembly is a chain of connected parts: the basket strainer or garbage disposal at the sink bottom, a tailpiece dropping down, the P-trap that holds water to block sewer gas, and the drain arm that runs into the wall.

The most common source is a slip-joint connection. These are the threaded plastic or chrome nuts that join the tailpiece to the trap and the trap to the drain arm. Inside each nut sits a beveled washer that compresses against the pipe to make the seal. Over time, heat, disposal vibration, and age flatten or crack those washers, and a nut can work itself loose. The result is a drip that appears only when water is running.

The second common source is the P-trap itself. Plastic traps can crack, especially at the molded seams or where a previous owner overtightened a nut. Chrome traps corrode from the inside out, so one that looks fine can be paper-thin at the bend. If water drips from the lowest point of the trap even when the nuts are tight, the trap body is the problem.

The third source is the basket strainer seal. The strainer sits in the sink opening with a ring of plumber's putty or a rubber gasket underneath. When that seal dries out or shrinks, water seeps around the rim of the strainer and drips down the outside of the tailpiece. A strainer leak often appears right after you fill the basin and let it drain. Less common sources include a cracked tailpiece, a loose dishwasher hose, and a failed disposal seal. Water dripping from the bottom of a disposal usually means the unit is worn out; see our guide to a garbage disposal leaking from the bottom.

Tools and Materials You Will Need

Most kitchen sink drain repairs need nothing more than a bucket, a towel, and a pair of channel-lock pliers, so gather everything before you start.

  • Bucket and old towels: Place the bucket under the trap before loosening anything.
  • Channel-lock pliers: For loosening and tightening slip-joint nuts.
  • Replacement slip-joint washers: Buy a multi-pack in the 1 1/2-inch size most kitchen sinks use.
  • Replacement P-trap: A complete plastic trap kit costs about $10 to $20 and includes new nuts and washers.
  • Plumber's putty: Needed only if you are resealing a basket strainer.
  • Flashlight, sponge, and dry rag: For spotting drips and drying pipes before a leak test.

Replacing a strainer may also need a strainer wrench to hold it from above. Check your trap and tailpiece size before buying parts. Most US kitchen sinks use 1 1/2-inch drain pipe, but some older homes have 1 1/4-inch.

How to Find the Exact Leak

Fixing the wrong joint wastes time and parts, so start by finding the exact source. Clear the cabinet, lay down a towel, and dry every pipe joint with a rag. Then run cold water in the sink for 30 seconds while you watch the drain assembly with a flashlight.

Work from the top down. First watch the strainer and tailpiece connection, then each slip-joint nut in turn, then the bottom of the trap. Trace any drip upward to the highest wet joint. That is your leak.

If nothing drips with the faucet running, fill the sink halfway and pull the plug. A full basin puts more pressure on the seal and trap, so hidden leaks often appear during a fast drain. If you have a garbage disposal, run it with water flowing and watch the disposal connections. If you have a dishwasher, run a short cycle and check its drain hose connection.

Note exactly which joint or part it is. A leak at a nut usually means a worn washer or a loose nut. A leak from the trap body means a cracked or corroded trap. A leak around the strainer rim means a failed seal. Each one has a different fix, covered below.

How to Fix a Leaky Slip-Joint Connection

A loose or worn slip joint is the easiest kitchen sink drain leak to fix, and it solves the problem in most cases. Put the bucket under the joint and run the faucet to confirm the source.

First, try simply tightening the nut by hand, then give it a quarter turn with channel-lock pliers. Do not overtighten. Plastic nuts crack easily, and overtightening a chrome nut can deform the washer. Dry the joint, run the water again, and check for drips. If it stops, check again after a day of use, since a marginal washer can leak again under hot water.

If tightening does not stop the drip, the washer inside is worn. Unscrew the nut, slide it back, and pull the washer out. Note which way the beveled side faces. The beveled edge always points toward the fitting it seals against, and installing it backward is the most common reason a new washer still leaks. Slide the new washer on in the same orientation, reassemble, and hand-tighten the nut plus a quarter turn with pliers.

While the joint is apart, check the pipe ends. If the tailpiece or trap arm is cracked, rough, or out of round, a new washer will not seal and the piece needs replacing. Also check that the pipes are aligned. If a trap arm enters the wall fitting at a visible angle, the joint is under stress and will keep leaking. Loosen the neighboring joints, realign the parts so they meet straight, and retighten.

How to Fix a Leaking P-Trap

If the trap body itself is cracked or corroded, or if the slip joints at both ends are in bad shape, replacing the whole trap is faster and more reliable than patching it. A plastic P-trap kit costs $10 to $20 and comes with everything you need.

Place the bucket under the trap and unscrew the two slip-joint nuts. Pull the old trap down and let the water inside drain into the bucket. Take the old trap to the store to match the size. Kitchen sinks normally use a 1 1/2-inch trap, sometimes with a cleanout plug.

Assemble the new trap loosely before installing it. Slide the nuts and washers onto the tailpiece and drain arm first, with the beveled sides of the washers facing the trap fittings. Then push the trap into place and hand-tighten both nuts. The trap should sit level, with the J-bend at the bottom and no twist on either joint. Tighten each nut a quarter turn past hand-tight with pliers.

Run water for a full minute and check both joints. If one still drips, loosen it, check the washer orientation, and retighten. If a nut will not thread smoothly by hand, back it off and start again rather than forcing it, since a cross-threaded nut will not seal. For a full step-by-step on installing drain parts, see our guide on how to install a kitchen sink drain. Never use a chemical drain cleaner while you have a leak. It can eat through a weakened trap or splash back when you open the joint, so clear slow drains with a snake or by removing the trap.

How to Fix a Leaking Basket Strainer

A leaking basket strainer takes more work than a slip joint, but it is still a manageable DIY job that takes about an hour. Remove the strainer, clean off the old seal, and reinstall it with fresh putty.

First, disconnect the tailpiece from the strainer by loosening the slip-joint nut below it. Then, from underneath the sink, loosen the large locknut that holds the strainer in place. You may need a strainer wrench or a second person holding it from above so it does not spin. Once the locknut is off, push the strainer up and out of the sink.

Scrape all the old putty off the strainer rim and sink opening, and clean both surfaces until smooth and dry. Old putty left behind will keep the new seal from sitting flat. Roll a pencil-thick rope of fresh putty and press it evenly around the underside of the strainer flange. Set the strainer back into the sink opening and press it down firmly.

From below, slide the rubber gasket and friction ring back onto the strainer body, then thread the locknut on and tighten it. Putty will squeeze out around the rim as you tighten. That is normal and means the seal is forming. Wipe away the excess, reconnect the tailpiece, and test by filling the basin and draining it, then check underneath for drips. If you are replacing the sink too, the strainer and sink should match, since a poor fit is a leak waiting to happen. Our roundup of the best kitchen sinks for 2026 covers the most common sink types and what fits each one.

When to Call a Plumber and What It Costs

Most kitchen sink drain leaks are DIY jobs, but some situations call for a professional. Call a plumber if the leak is inside the wall, the drain arm is corroded into the wall fitting, you find mold or rotted wood, or the leak returns after a proper fix. A recurring leak can mean a misaligned drain line or a blocked vent. Also call a plumber if the sink still drains slowly after the trap is clean, which can point to a blockage farther down the line.

RepairTypical cost (2026)DIY or pro
Slip-joint washer replacement$5-$15 in partsDIY, under 30 minutes
Full P-trap replacement$10-$25 in partsDIY, 30-60 minutes
Basket strainer reseal$5-$10 in partsDIY, about 1 hour
Plumber visit to fix a drain leak$150-$350Pro, usually 1 hour
Garbage disposal replacement (if the leak is the disposal)$200-$450 installedPro recommended
Cabinet floor repair from water damage$200-$600Pro recommended

Rates vary by region, and after-hours calls cost more. In 2026, most plumbers charge $75 to $150 per hour, with a minimum service fee of $100 to $150. A simple trap or strainer repair usually falls at the low end because it takes about an hour, while damaged pipe inside the wall costs more.

The cheapest fix is the fast one. A drip that runs for a month can ruin a cabinet floor that costs hundreds to replace, so do not put off a leak you have already found. Dry the cabinet, find the source, and fix the joint or replace the part the same day. For more kitchen plumbing help, browse our kitchen plumbing guides. If the repair is beyond your comfort level, or the leak keeps returning after a proper fix, get a plumber out before the water damage spreads. For help with a kitchen sink drain leak, call (877) 762-1902.

Frequently Asked Questions

Why does my kitchen sink drain leak only when the dishwasher runs?
The dishwasher drains through a hose connected to the garbage disposal or tailpiece. If that hose connection is loose or its clamp is worn, water leaks only during the dishwasher cycle. Tighten or replace the hose clamp and check the hose for cracks.
Can I use plumber's putty on a plastic sink?
No. Plumber's putty can stain and damage some plastic and composite sinks. Use a silicone-based sealant or the rubber gasket supplied with the strainer instead, and check the sink manufacturer's instructions first.
How tight should a slip-joint nut be?
Hand-tight plus about a quarter turn with pliers. Overtightening cracks plastic nuts and deforms washers, which causes the very leak you are trying to fix. If it still drips after a quarter turn, replace the washer instead of tightening further.
Is a leaking kitchen sink drain an emergency?
A slow drip is not an emergency, but it should be fixed the same day. A steady stream of water, or a leak you cannot stop by turning off the faucet, is urgent: place a bucket under it, stop using the sink, and call a plumber.
Why does my new P-trap still leak?
The most common causes are a washer installed backward, a cross-threaded nut, or pipes that meet at an angle. Loosen both nuts, check the washer orientation, realign the trap so it sits straight, and retighten by hand plus a quarter turn.
Does a kitchen sink drain leak cause mold?
Yes, if it goes unnoticed. A slow leak keeps the cabinet damp, and mold can start growing on wood and drywall within 24 to 48 hours. Dry the cabinet fully after the repair and check for soft or discolored wood.
AP
ABS Pipes Editorial Team
Our guides are researched from plumbing codes, manufacturer specs and licensed-plumber interviews, then reviewed for accuracy before publishing. Prices are re-verified periodically — see the "last verified" note on cost guides.
Disclaimer: This content is for informational purposes only and is not licensed plumbing advice. Plumbing work can involve water damage, gas lines and code violations — when in doubt, hire a licensed plumber in your area.