Garbage Disposal Jammed: How to Fix It
A garbage disposal jammed is a frustrating kitchen problem, but it is also one of the easiest appliance fixes in the house. Most jams happen because something hard, a bone, a bottle cap, a piece of silverware, a fruit pit, got wedged between the spinning flywheel and the shredder ring. The motor stalls, the unit hums or goes silent, and the sink stops draining. Before you call a plumber or buy a new disposal, try the steps below. In most cases, you can free the jam in ten minutes with the Allen wrench that came with the unit, and you will not need any special tools or parts.
What Jams a Garbage Disposal
Garbage disposals are built to grind soft food scraps, not hard objects. The most common jam culprits are chicken bones, fruit pits, bottle caps, twist ties, silverware, and small pieces of glass or ceramic. Fibrous foods like celery strings, artichoke leaves, and corn husks can also wrap around the flywheel and stall it, especially in older or lower-horsepower units. Grease is another quiet cause: it hardens inside the chamber, coats the flywheel, and makes the motor work harder until it trips the overload protector.
Age matters too. In a disposal that is eight to twelve years old, the internal bearings wear down, the flywheel gets stiff, and the motor loses torque. A unit that used to grind through scraps without complaint starts jamming on smaller and smaller loads. If your disposal jams every week even though you are careful about what goes in, worn internals are probably the real problem, and replacement is worth considering. Our guide on how long garbage disposals last explains the warning signs that a unit is near the end of its life.
Sometimes the problem is not a jam at all. If the disposal makes no sound when you flip the switch, the issue may be a tripped GFCI outlet, a blown fuse, or a failed switch. Check the outlet first by plugging in another appliance, and check the reset button on the bottom of the unit before assuming the motor is dead. If the unit hums but does not spin, that is the classic sign of a jam, and the steps below will fix it.
Safety First: What Never to Do
A garbage disposal is a powerful appliance with sharp grinding teeth, so safety comes before any repair. Never, ever put your hand inside the disposal chamber, even if you are sure the power is off. The flywheel can move unexpectedly, and the shredder ring is sharp enough to cause a serious cut. Use tongs, needle-nose pliers, or a wooden spoon handle to fish objects out, never your fingers.
Before you start, turn off the power at the wall switch, and if your disposal plugs into an outlet under the sink, unplug it. If it is hardwired, flip the breaker for the kitchen circuit. This is not optional. Accidentally flipping the switch while you are working underneath the unit is the most common way people get hurt during this repair. Keep the switch off until the jam is fully cleared and you are ready to test.
Also, never use chemical drain cleaners in a disposal. Caustic cleaners can damage the seals, splash back when the unit runs, and create a hazard for anyone who works on it later. Never pour boiling water into a jammed disposal either, since it can warp plastic parts and does nothing to free a mechanical jam. And never run the disposal for more than a few seconds while it is jammed and humming. A stalled motor draws heavy current and overheats quickly, and running it jammed can burn out the motor and turn a ten-minute fix into a full replacement.
Step 1: Press the Reset Button
Every garbage disposal has a small red reset button on the bottom of the unit. When the motor jams and overheats, a built-in overload protector trips and cuts power, and the button pops out. Before you do anything else, look under the sink, find the red button on the underside of the disposal, and press it firmly until it clicks and stays in. If it pops right back out, the jam is still there, so move on to the next step and come back to the button later.
While you are under the sink, check the power cord and the outlet. If the disposal is plugged in and the outlet has a GFCI reset button, press that too. A tripped GFCI is a common reason a disposal goes completely silent, and it takes two seconds to check. If your disposal is hardwired, confirm the breaker is on. Once the reset button is pressed and power is confirmed, flip the switch and see if the disposal runs. If it starts normally, the jam may have been a one-time overload, and you are done. If it hums, buzzes, or does nothing, the flywheel is still stuck, and the Allen wrench is your next tool. For more on this button and other simple fixes, see our guide on how to reset a garbage disposal.
Step 2: Free the Flywheel With an Allen Wrench
Look at the very bottom center of the disposal. You will see a hexagonal socket. This is the manual crank for the flywheel, and it takes a 1/4-inch Allen wrench, the same size that comes taped to most new disposals. If you do not have the original wrench, any standard 1/4-inch Allen key works, and they cost a few dollars at any hardware store.
Insert the Allen wrench into the socket and work it back and forth, turning a quarter turn clockwise, then a quarter turn counterclockwise. At first, the flywheel may barely move. Keep working it gently, increasing the range of motion a little at a time. You should feel resistance give way as the object wedged in the chamber shifts. Never force the wrench with excessive leverage, since that can crack the flywheel or damage the motor shaft, but a firm, steady rocking motion is exactly what this socket is designed for.
After a minute or two of rocking, the flywheel should spin freely through a full rotation in both directions. When it does, remove the wrench, press the reset button again, restore power, and run cold water into the sink. Flip the switch and let the disposal run for thirty seconds with the water running. The cold water flushes ground-up debris down the drain and keeps the motor cool. If the unit runs smoothly and drains well, the jam is cleared. If it still hums or stalls, the object is still in there, and you need to remove it by hand, with tools, from above.
Step 3: Remove the Object Causing the Jam
If the flywheel spins freely with the wrench but the disposal still jams under power, or if you can see something lodged in the chamber, the object needs to come out. With the power still off and the unit unplugged, shine a flashlight down into the disposal from the sink drain. Look for anything that does not belong: a spoon, a cap, a shard of glass, a bone. Use long-handled tongs or needle-nose pliers to grab it and pull it out. Work slowly and keep your fingers out of the drain opening.
If you cannot see the object, try working the flywheel from below with the Allen wrench again while someone watches from above, or use a wooden broom handle pressed against the flywheel through the drain opening to nudge it. A plunger can also help: with the disposal off, place a sink plunger over the drain and pump a few times to dislodge loose debris, then fish it out with tongs. Once you believe the chamber is clear, press the reset button, restore power, and test with cold water running. If the disposal grinds normally and the sink drains, run a handful of ice cubes through it to scour the grinding chamber, followed by a few lemon halves to freshen it.
Glass is the hardest jam to clear, because shards wedge into the shredder ring and are difficult to see. If you suspect broken glass, use a wet and dry vacuum to suck debris out of the chamber before trying the wrench again, and wear heavy gloves when handling anything you pull out. If you cannot find or remove the object after several tries, stop and call a plumber. Forcing the issue risks damaging the unit or injuring yourself, and a professional can remove the disposal and clear it from below. Our garbage disposal repair cost guide covers what a service visit typically runs in 2026.
When Repair Is Not Worth It
Most jams are a one-time event, but some patterns mean the disposal itself is failing. If the unit jams weekly, leaks from the bottom seal, makes a loud grinding or rattling noise even when empty, or needs the reset button pressed every time you use it, the motor or the internal seals are wearing out. A disposal that is more than ten years old and jamming regularly is usually not worth a professional repair, since a service visit can cost $100 to $200, while a new mid-range unit costs $150 to $350 installed.
Leaks are a separate red flag. Water dripping from the bottom of the unit means the internal seals have failed, and no amount of unjamming will fix that. A leak at the top, where the disposal meets the sink flange, is usually a worn gasket and is worth fixing, but a bottom leak means replacement. If you decide to replace the unit, a 1/2 horsepower model suits most households, while a 3/4 horsepower model handles heavier use and fibrous foods better. Our best garbage disposals of 2026 roundup compares the top models by power, noise, and price.
How to Prevent Future Jams
Prevention is mostly about what goes down the drain. Always run cold water before, during, and for thirty seconds after using the disposal. Cold water keeps grease solid so it gets ground up and flushed away instead of coating the chamber. Feed food in small amounts rather than dumping a whole plate at once, and let the disposal finish grinding one batch before adding more. Never put bones, fruit pits, coffee grounds, pasta, rice, potato peels, or fibrous vegetables like celery and asparagus in the disposal. These are the foods that cause most jams.
Keep silverware, bottle caps, and twist ties far from the sink while the disposal is running, and check plates for small items before scraping them. Once a month, grind a tray of ice cubes to scour the chamber walls, and run a few citrus peels through to keep it fresh. Avoid putting grease or oil down the drain entirely, since it hardens in the pipes below the disposal and causes slow drains that feel like a jam. With careful use, a good disposal should run for eight to twelve years with only the occasional jam, and when one does happen, you now know exactly how to clear it.
Frequently Asked Questions
Jam questions usually boil down to safety, the right tool, and whether the unit is worth saving. The answers below cover the most common ones, including what to do when the reset button will not stay in and when a humming disposal means something worse than a simple jam.