Kitchen Faucet Leaking at Base: How to Fix It

A kitchen faucet leaking at base is one of the most common sink problems in American homes, and it usually starts as a small puddle that appears around the bottom of the faucet after you run the water. Left alone, that slow leak soaks into the countertop, swells particleboard, stains the cabinet floor, and can even grow mold under the sink. The good news is that most base leaks come from just three causes: a loose mounting nut, a worn O-ring, or a failing cartridge. All three are fixable with basic tools in under an hour, and this guide walks you through each one in order, from the easiest fix to the deeper repair.

Key takeaway: A kitchen faucet leaking at the base is usually caused by a loose mounting nut, a worn O-ring, or a bad cartridge. Start by tightening the mounting nut under the sink, then replace the O-rings, and finally swap the cartridge if the leak continues. Most homeowners can finish the whole job in under an hour with a basin wrench and a screwdriver.

What Causes a Kitchen Faucet to Leak at the Base

Water pooling at the base of your faucet can come from a few different places, and finding the real source saves you from replacing parts that are still fine. The most common culprit is a worn O-ring. The spout of most kitchen faucets rotates on one or two rubber O-rings that seal the joint between the spout and the faucet body. Every time you swing the spout from one side of the sink to the other, those rings wear a little more. After five to ten years of daily use, they flatten and crack, and water starts seeping out at the base of the spout whenever the faucet runs.

The second common cause is a loose mounting nut. Your faucet is held to the sink or countertop by a large nut underneath, and vibration from the water running, plus the constant tugging of a pull-down sprayer hose, can slowly loosen it over time. When the faucet body can wiggle even slightly, water finds its way under the base plate and out onto the counter. This is the easiest fix of all, and it is always worth checking first.

The third cause is a worn cartridge or valve inside the faucet body. The cartridge controls the flow and temperature of the water, and when its internal seals fail, water can travel up through the body and leak out at the base instead of coming through the spout. If your faucet also drips from the spout when it is turned off, or the handle feels stiff or gritty, the cartridge is the likely problem. Less often, the leak comes from a cracked faucet body, a failed sprayer hose connection, or deteriorated plumber putty under the base plate. If you see water only when the sprayer is used, check the sprayer hose connection first. If the faucet body itself is cracked or corroded, repair is not practical and replacement is the better move. Our kitchen faucet replacement guide covers that job step by step.

Tools and Supplies You Will Need

Gather everything before you start so you are not running to the hardware store with the water shut off. You will need an adjustable wrench, a basin wrench for the hard-to-reach mounting nut under the sink, a Phillips and a flat-head screwdriver, an Allen wrench set for the handle set screw, and a pair of slip-joint pliers. Keep a bucket and old towels nearby to catch water left in the lines, and a flashlight or headlamp, because the space under a kitchen sink is always dark.

For parts, buy a faucet repair kit or a set of O-rings that match your faucet brand and model. If you know the brand, Delta, Moen, Kohler, or Pfister, take a photo of the model number, usually printed on a tag on the supply lines, and bring it to the store. You may also need a replacement cartridge, silicone faucet grease, and plumber putty or a new base gasket. A small tube of silicone grease costs a few dollars and makes a real difference: it keeps new O-rings from tearing during installation and helps them seal. If you are unsure which cartridge fits, remove the old one first and bring it with you to match it at the store.

Step 1: Shut Off the Water and Prep the Sink

Before you touch the faucet, turn off the water. Look under the sink for two shut-off valves, one on the hot line and one on the cold line. Turn each one clockwise until it stops. Then open the faucet and let any water left in the lines drain into the sink. If your shut-off valves are stuck, corroded, or missing, turn off the main water supply to the house instead and plan to replace those valves soon, because working shut-offs make every future repair much easier.

Next, clear everything out from under the sink and put a bucket and towels underneath the faucet connections. Plug the sink drain with a rag or a stopper so small screws and clips cannot fall down the drain. Take a photo of the faucet from above and below before you take anything apart. That photo is your map for putting everything back together, and it costs you ten seconds. Finally, note which handle controls hot and which controls cold, and mark the cartridge orientation if you plan to remove it, because installing a cartridge backward reverses hot and cold.

Step 2: Tighten the Base and Mounting Nut

The first fix to try is also the simplest. Get under the sink with your flashlight and find the mounting nut that holds the faucet to the sink deck. It is a large plastic or metal nut threaded onto the faucet shank, often with a metal washer and a rubber gasket above it. Reach up with your basin wrench and tighten the nut by turning it clockwise. Do not over-tighten, since too much force can crack a porcelain sink or crush the gasket, but snug it firmly until the faucet no longer wiggles when you push it from above.

While you are under there, check the supply line connections where the hot and cold lines meet the faucet. A slow drip from a loose supply connection can run down the line and look like a base leak from above. Snug each connection a quarter turn with your wrench and dry everything with a towel. Then turn the water back on and run the faucet for a minute while you watch the base. If the leak is gone, you are done. If the faucet still leaks, the problem is inside the faucet body, so move on to the O-rings.

Also check the base plate or escutcheon, the decorative cover that sits on the counter around the faucet. If it rocks or lifts, water can get underneath it. Lift it gently, clean off any old putty or grime, and apply a thin bead of plumber putty or silicone sealant under the edge before pressing it back down. This seals the gap so splashed water cannot sneak underneath and pool at the base.

Step 3: Replace Worn O-Rings and Seals

If tightening did not stop the leak, the O-rings are the next suspect. Shut the water off again, then remove the spout. On most kitchen faucets, the spout is held by a small retaining nut or a clip at the base, and sometimes by a set screw on the back of the faucet body. Loosen the nut or remove the screw, then pull the spout straight up with a gentle twisting motion. If it sticks, wiggle it side to side rather than forcing it, because forcing a stuck spout can damage the faucet body.

Once the spout is off, you will see one or two black rubber O-rings seated in grooves on the faucet body, or inside the base of the spout. Slide them off with a small flat-head screwdriver or a pick, taking care not to scratch the metal grooves. Compare the old rings to the new ones from your repair kit. They should match in thickness and diameter. If the old rings are flattened, cracked, or stretched out of shape, you have found your leak.

Before installing the new rings, clean the grooves with a cloth and a little white vinegar to remove mineral buildup and old grease. Coat the new O-rings lightly with silicone faucet grease, then roll them into the grooves, making sure they sit flat and are not twisted. Reinstall the spout by pressing it straight down and turning it gently until it seats, then tighten the retaining nut or replace the clip. Turn the water back on and test. In most cases, fresh O-rings stop a base leak completely, and the whole job takes about twenty minutes. For a full rundown of faucet part costs, see our guide to faucet cartridge replacement cost.

Step 4: Replace the Cartridge

If the leak persists after new O-rings, the cartridge is the last internal part to check. The cartridge sits inside the faucet body under the handle. Start by prying off the small decorative cap on the handle, usually marked with a red and blue dot, to reveal the set screw. Loosen the set screw with an Allen wrench and pull the handle straight off. Then unscrew the dome cap or retaining nut on top of the faucet body to expose the cartridge.

Pull the cartridge straight up. If it resists, use pliers on the stem and rock it gently side to side. Note the orientation of the cartridge before you remove it, especially any notches or tabs that line up with the body. Take the old cartridge to the hardware store and match it exactly, since cartridges are brand and model specific and a close match will not seal properly. Many manufacturers, including Moen and Delta, offer free replacement cartridges under a lifetime warranty, so it is worth checking the brand website before you buy one.

Before installing the new cartridge, flush the faucet body by briefly turning the water on with the cartridge removed, catching the spray with a towel. This clears out grit and mineral deposits that could damage the new seals. Then drop the new cartridge in, aligned exactly as the old one was, tighten the retaining nut, and reassemble the handle. Turn the water on slowly and check the base while you run the faucet through hot, cold, and mixed settings. A new cartridge should stop both the base leak and any dripping from the spout.

When to Call a Plumber

Most base leaks are do-it-yourself repairs, but there are times when a plumber is the smarter call. If the faucet body is cracked, corroded through, or pitted with mineral damage, no new seal will hold, and the faucet needs to be replaced. If the shut-off valves under the sink are frozen, leaking, or broken, a plumber can replace them and fix the faucet in the same visit. If you have taken the faucet apart twice and the leak keeps coming back, there may be a hairline crack or a damaged valve seat that is hard to spot without experience.

Also call a professional if you notice water damage under the sink, soft or swollen cabinet wood, or a musty smell that suggests a long-running hidden leak. A plumber can check for damage to the supply lines and the drain assembly at the same time. Expect to pay $100 to $250 for a professional faucet repair in 2026, and $150 to $550 for a full replacement including the new faucet. Compare that with the $10 to $40 in parts for a do-it-yourself O-ring and cartridge job. If you are planning a replacement, our kitchen faucet installation cost guide breaks down plumber rates and faucet prices so you can budget the job.

Frequently Asked Questions

Base leaks are common and usually simple to fix, but a few questions come up on almost every job. The answers below cover the most frequent ones, including whether a leak can wait, what to do when the faucet still leaks after new parts, and how long a repair should last.

Frequently Asked Questions

Why is my kitchen faucet leaking at the base?
The most common causes are a loose mounting nut, worn O-rings on the spout, or a failing cartridge. Tighten the mounting nut first, then replace the O-rings, and replace the cartridge if the leak continues.
Can I use my faucet while it is leaking at the base?
You can use it briefly, but do not ignore the leak. Water pooling at the base soaks into the countertop and cabinet, causing swelling, stains, and mold. Fix it within a few days at most.
How much does it cost to fix a faucet leaking at the base?
A DIY repair costs $10 to $40 in parts for O-rings or a cartridge. A plumber typically charges $100 to $250 to repair a base leak in 2026.
How do I know if the O-rings or the cartridge is the problem?
If water leaks from the base of the spout when you swing it side to side, the O-rings are likely worn. If the faucet also drips from the spout when off, or the handle feels stiff, the cartridge is the likely cause.
Do I need to shut off the water to fix a base leak?
Yes. Always shut off the hot and cold valves under the sink before removing the spout or cartridge. If those valves do not work, shut off the main water supply to the house.
How long do faucet O-rings last?
Faucet O-rings typically last 5 to 10 years depending on water hardness and how often the spout is moved. Hard water shortens their life, so replacing them during any faucet repair is good practice.
AP
ABS Pipes Editorial Team
Our guides are researched from plumbing codes, manufacturer specs and licensed-plumber interviews, then reviewed for accuracy before publishing. Prices are re-verified periodically — see the "last verified" note on cost guides.
Disclaimer: This content is for informational purposes only and is not licensed plumbing advice. Plumbing work can involve water damage, gas lines and code violations — when in doubt, hire a licensed plumber in your area.